sort out jtag config files

tools/jtag_openocd/chip-at91sam7s.cfg

@@ -0,0 +1,30 @@
+## Chipset configuration section
+# use combined on interfaces or targets that can't set TRST/SRST separately
+reset_config srst_only srst_pulls_trst
+
+jtag newtap sam7x cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id 0x3f0f0f0f
+
+target create sam7x.cpu arm7tdmi -endian little -chain-position sam7x.cpu
+
+sam7x.cpu configure -event reset-init {
+	soft_reset_halt
+	mww 0xfffffd00 0xa5000004	# RSTC_CR: Reset peripherals
+	mww 0xfffffd44 0x00008000	# WDT_MR: disable watchdog
+	mww 0xfffffd08 0xa5000001	# RSTC_MR enable user reset
+	mww 0xfffffc20 0x00005001	# CKGR_MOR : enable the main oscillator
+	sleep 10
+	mww 0xfffffc2c 0x000b1c02	# CKGR_PLLR: 16MHz * 12/2 = 96MHz
+	sleep 10
+	mww 0xfffffc30 0x00000007	# PMC_MCKR : MCK = PLL / 2 = 48 MHz
+	sleep 10
+	mww 0xffffff60 0x00480100	# MC_FMR: flash mode (FWS=1,FMCN=72)
+	sleep 100
+}
+
+gdb_memory_map enable
+#gdb_breakpoint_override hard
+#armv4_5 core_state arm
+
+sam7x.cpu configure -work-area-virt 0 -work-area-phys 0x00200000 -work-area-size 0x10000 -work-area-backup 0
+flash bank sam7x.flash.0 at91sam7 0 0 0 0 sam7x.cpu 0 0 0 0 0 0 0 18432
+flash bank sam7x.flash.1 at91sam7 0 0 0 0 sam7x.cpu 1 0 0 0 0 0 0 18432

tools/jtag_openocd/interface-armusbocd.cfg

@@ -0,0 +1,12 @@
+#define our ports
+telnet_port 4444
+gdb_port 3333
+
+#commands specific to the Olimex ARM-USB-OCD Dongle
+interface ft2232
+ft2232_device_desc "Olimex OpenOCD JTAG"
+ft2232_layout "olimex-jtag"
+ft2232_vid_pid 0x15BA 0x0003
+jtag_speed 2
+jtag_nsrst_delay 200
+jtag_ntrst_delay 200

tools/jtag_openocd/interface-busblaster.cfg

@@ -0,0 +1,14 @@
+## General OpenOCD configuration
+# Ports
+telnet_port 4444
+gdb_port 3333
+
+interface ftdi
+ftdi_device_desc "Dual RS232-HS"
+ftdi_vid_pid 0x0403 0x6010
+
+ftdi_layout_init 0x0c08 0x0f1b
+ftdi_layout_signal nTRST -data 0x0100 -noe 0x0400
+ftdi_layout_signal nSRST -data 0x0200 -noe 0x0800
+
+adapter_khz 1000

tools/jtag_openocd/interface-buspirate.cfg

@@ -0,0 +1,20 @@
+# Ports
+telnet_port 4444
+gdb_port 3333
+
+# Interface
+interface buspirate
+buspirate_port /dev/ttyUSB0
+adapter_khz 1000
+
+# Communication speed
+buspirate_speed normal # or fast
+
+# Voltage regulator: enabled = 1 or disabled = 0
+buspirate_vreg 1
+
+# Pin mode: normal or open-drain
+buspirate_mode normal
+
+# Pull-up state: enabled = 1 or disabled = 0
+buspirate_pullup 1

tools/jtag_openocd/interface-jlink.cfg

@@ -0,0 +1,7 @@
+#define our ports
+telnet_port 4444
+gdb_port 3333
+
+interface jlink
+transport select jtag
+adapter_khz 1000

tools/jtag_openocd/interface-jtagkey.cfg

@@ -0,0 +1,12 @@
+#define our ports
+telnet_port 4444
+gdb_port 3333
+
+#commands specific to the Amontec JTAGKey
+interface ft2232
+ft2232_device_desc "Amontec JTAGkey A"
+ft2232_layout jtagkey
+ft2232_vid_pid 0x0403 0xcff8
+jtag_khz 200
+jtag_nsrst_delay 200
+jtag_ntrst_delay 200

tools/jtag_openocd/interface-wiggler.cfg

@@ -0,0 +1,9 @@
+telnet_port 4444
+gdb_port 3333
+
+interface parport
+parport_port 0x378
+parport_cable wiggler
+jtag_speed 0
+jtag_nsrst_delay 200
+jtag_ntrst_delay 200

tools/jtag_openocd/openocd_flash_recovery.sh

@@ -0,0 +1,12 @@
+#!/bin/bash
+
+# Example for 512kb version, using Segger Jlink:
+CONFIG_CHIP=chip-at91sam7s.cfg
+CONFIG_IF=interface-jlink.cfg
+IMAGE=../../recovery/proxmark3_recovery.bin
+
+if [ ! -e "$IMAGE" ]; then
+    echo "$IMAGE missing. Abort!"
+    exit 1
+fi
+openocd -f $CONFIG_IF -f $CONFIG_CHIP -c "init;halt;flash erase_sector 0 0 15;flash erase_sector 1 0 15;flash write_image $IMAGE 0x100000;exit"